Technical Knowledge: Analysis of various causes of water pump out

(1) The pump is not filled with enough water prior to start-up, and sometimes it appears that the water has been spilled from the bleed hole, but the air is not completely discharged by the pump shaft, causing a small amount of air to remain in the inlet pipe or pump body.

(2) The horizontal section of the inlet pipe in contact with the pump applies a descending gradient of 0.5% or more to the direction of the flow of water, and the one end connected to the inlet of the pump is the highest, not completely horizontal. If you tilt up, there will be trapped air inlet pipe, reducing the vacuum hose and pump, affecting water absorption.

(3) The packing of the pump is worn or the packing pressure is too loose due to the long-term use, resulting in a large amount of water being ejected from the gap between the packing and the shaft sleeve of the pump. As a result, external air enters the pump from these gaps, Affected the mention of water.

(4) Inlet pipe Due to long-term potential underwater, pipe wall corrosion holes, water pumps continue to decline after work, when these holes exposed water, the air from the hole into the civilian into the water pipe.

(5) cracks in the inlet pipe cracks, inlet pipe and pump connections appear tiny gaps, are likely to make the air into the inlet pipe.

Pump speed is too low

(1) human factors. Some users due to the original motor damage, it is coupled with another motor driven, the result of a small flow, low lift or even the consequences of the water.

(2) the pump itself mechanical failure. Impeller or shaft fastening nut loose shaft bending deformation, resulting in multi-shift impeller, direct friction with the pump, or bearing damage, are likely to reduce the pump speed.

(3) power machine repair is not working. Motor due to the winding burned, and lost magnetism, the maintenance of the winding turns, diameter, wiring changes, or maintenance failure is not completely ruled out the factors that will change the pump speed.

Suction too much

Some of the water is deep and some of the water's outer surface is flat, ignoring the allowable suction of the pump, resulting in little or no water absorption. To know the pump suction port can establish a degree of vacuum is limited, the absolute vacuum suction is about 10 meters high water column, and the pump can not establish an absolute vacuum. And the vacuum is too large, easy to pump the water gasification, the work of the pump negative. Therefore, the centrifugal pump has its maximum allowable suction, usually between 3-8.5 meters. Do not install the pump only easy and simple.

Water flow in the water pipe resistance loss is too large

Some users through the measurement, although the vertical distance from the reservoir or water tower to the water surface is slightly less than the head of the pump, but still small amount of water or mention the water. The reason is often the pipeline is too long, multi-bend pipes, water pressure loss in the pipe is too large. The reason is often too long pipes, pipe corners, water flow resistance in the pipeline is too large loss. Under normal circumstances 90-degree bend than the 120-degree elbow bend resistance, each 90-degree elbow head loss of about 0.5-1 meters, every 20 meters pipeline resistance can make head loss of about 1

Meter. In addition, some users are also free to pump into and out of the pipe diameter, which also has a certain impact on the lift.

Other factors

(1) The bottom valve can not open. It is usually due to the pump being left on for too long, the bottom valve gasket is stuck, and the bottom valve without gasket may rust.

(2) The bottom valve filter screen is clogged; or the bottom valve causes potential clogging of the filter screen in the sludge layer.

(3) impeller wear serious. Impeller blades worn by long-term use, affecting the pump performance.

(4) Gate valve can check valve failure or blockage will result in reduced flow or even pumping on the water.

(5) Leakage of the outlet pipe will also affect the amount of water lift.

hydraulic block valve 100L/min

Max. Flow: 100L/min

Pressure: 310Bar

GKV100 series

GKV100 proportional valve is a stackable valve with interchangeable control styles.

Electro-Hydraulic pilot valves can be either 12 VDC or 24 VDC,corresponding current is 0-1.5 or 0-0.75Amp.

This series can provide following functions:

- Inlet module with pilot supply.

- Inlet module without pilot supply.

- A/B Port with overload valve on main section

- A Port with overload valve on main section

- B Port with overload valve on main section

- A/B Port with P.O. check

- A Port with P.O. check

- B Port with P.O. check

- End Cap with oil return function

- End Cap without oil return function

We can also choose other cartridges according to your requirement.

Valve Block

Valve Block,Standard Valve Block,Alloy Valve Block,Hydraulic Valve Block

Hangzhou Hanray Industry Co., Ltd , https://www.aircompressor.pl