Road sweeper is a multifunctional sanitation vehicle that is specially designed for garbage disposal on the road surface. It can be used as a substitute for manpower. It is mainly used for ground cleaning, roadside cleaning, road cleaning, and ground sprinkling. A new type of high-efficiency cleaning equipment integrating road cleaning, garbage recycling and transportation. Then we must ensure its safety when using it, because the safety performance on the road is more difficult to control. Steps: 1. When driving the sweeper, you should look around and observe whether there are people and obstacles around the vehicle. Have pedestrians and vehicles pass by before and after. If it is safe, then shut the door firmly, turn on the turn signal, and start the Midi. . 2. When the vehicle is moving, there must be serious people standing between the front and rear tires and between the boom and the front frame. 3. The water temperature must not be lower than 50 degrees at the start, start with a low speed block, avoid high speed advance. This must be remembered. 4. The sweeper should not be allowed to get in or out of the car while driving. The speed should be kept at 15/h. Do not think it is running at a low speed. You can make a special case. If any accident happens, you will regret it. 5. In winter, vehicles may be under conditions of rain, snow, mud and other bad conditions, but they must pay attention to anti-skid, to ensure its safety before cleaning operations can be avoided to avoid acceleration to avoid accidents caused by loss of control. 6. Of course, we must pay attention to observing the working conditions, braking, steering and other parts of the vehicle to see if it has any effect on the safety mechanism of the vehicle. If something happens on the way, we must stop driving, get off the vehicle and avoid driving. 7. As the roads are now vast, so that more and more garbage, so if the bucket is full, it must be timely dumping of waste, bucket opening and closing of the cover should be carried out slowly to avoid greater impact. 8. It is the easiest operation to clean up when there are winding objects on the roller. However, some operators will be lazy and should not have such a mentality. Safety is the first. 9. The minimum height of sweeper sweeper adjustment is that the substrate of the sweeping roller cannot contact with the bucket. It should be checked at a proper time, otherwise the angle will cause damage to the sweeper. 10. After completion of the clean-up work, it should be idling for 3-5 minutes before the flameout. This is to prevent damage caused by the supercharger speed. 11. After parking, put the joysticks in the neutral position, cut off the power, pull the handbrake, and make all the preparations for the car. 12. Close the doors and windows, lock the door, park it neatly, and fill in the usage records When we want to buy a road sweeper , we must clearly understand its performance and characteristics, proceed according to its mode of operation, and regularly carry out maintenance on the vehicle, just like the cars in our own home, in order to improve the road. The life of the sweeper! Airless Spray Gun Airless Spray Gun Airless Spray Gun,Plunger Rod,Spray Paint Gun,Electric Paint Spray Gun Fuzhou HVBAN Mechanical Equipment Co., Ltd. , https://www.hi-sprayer.com
This process occurs when paint is applied to an object through the use of an air-pressurized Spray Gun. The Sprayer Gun has a nozzle, paint basin, and air compressor. When the trigger is pressed the paint mixes with the compressed air stream and is released in a fine spray.
Types of nozzles and sprays
Due to a wide range of nozzle shapes and sizes, the consistency of the paint can be varied. The shape of the workpiece and the desired paint consistency and pattern are important factors when choosing a nozzle. The three most common nozzles are the full cone, hollow cone, and flat stream.There are two types of air-gun spraying processes. In a manual operation method the air-gun sprayer is held by a skilled operator, about 6 to 10 inches (15–25 cm) from the object, and moved back and forth over the surface, each stroke overlapping the previous to ensure a continuous coat.In an automatic process the gun head is attached to a mounting block and delivers the stream of paint from that position. The object being painted is usually placed on rollers or a turntable to ensure overall equal coverage of all sides.
How to use road sweeper safer